DIY Pill Bottle Opener (with Video Tutorial)
This easy DIY pill bottle opener is an easy sewing project perfect for beginners! Using simple stitches and inexpensive materials, you can quickly make a pill bottle gripper in 15 minutes or less!
Materials Used
A pill bottle opener uses fabric as well as a grippy material, such as shelf liner or rug grips.
I used leftover materials from making this DIY Jar Opener. You can easily make both items using the same supplies.
I used shelf liner from the Dollar Tree. It comes in a variety of colors so you can mix and match with your fabric.
Rug grip is similar to shelf liner and can be used, as well.
How to Make a Pill Bottle Opener
Supplies
- One 5 in X 5 in (13 X 13 cm) fabric square
- 5 in X 5 in Shelf Liner or Rug Grip
- Sewing Clips
- Thread
- Sewing Machine
- Turning Tool (optional)
Directions
Step 1
Cut one square of fabric to be 5 inches by 5 inches (13 cm X 13 cm).
Cut one 5 inch X 5 inch piece of shelf liner or rug grip.
Now is a good time to press out any wrinkles in your fabric.
Step 2
Layer the fabric and shelf liner in the following way:
- Shelf liner
- Fabric piece with pretty side (right side) facing down
Secure the edges together using sewing clips or pins.
Allow a 2-3 inch gap on one side so that you can turn the fabric inside out after sewing.
Helpful Tip: Clips are SO much easier to use than pins for this project! Well worth the few dollars they cost. You could also use clothespins, instead.
Step 3
Sew around all of the edges of the square using a 1/2 inch seam allowance. Be sure to leave a 2-3 inch gap that is not sewn shut.
Backstitch at the beginning and end of your stitching line to reinforce the seams.
When you get to a corner of the square, be sure that the needle is inserted in the fabric, then lift up the presser foot and move the fabric 90 degrees. Put the presser foot back down and continue stitching a straight line.
Step 4
Clip the corners to remove excess bulk. Be sure not to cut the stitching, but get close to the stitched corner.
If you would like, you can remove more excess by trimming the seam allowances to be about 1/8 inch wide. If you trim the seam allowances, be sure to leave the open seam allowance area with a larger width so that it is easy to turn under in the next step.
Turn the square inside out, with the shelf liner being on one side and the fabric on the other after it is turned.
Use a turning tool or your finger to press out each of the four corners.
Step 5
Turn under the open seam allowances and tuck in the unfinished edges inward. Clip together to hold in place.
Top-stitch around the outer edge of the square, with the fabric side facing up (not the shelf liner side).
Sew close to the edge of the pill bottle gripper, about 1/8 inch. Be sure to close the open seam allowance as you are top-stitching.
Step 6 (Optional)
You can stitch a large “X” across the square to prevent the fabric from bunching up. Start in one corner and stitch a straight line diagonally to the opposite corner. Then repeat on the other side.
Watch my YouTube video below to see how I made this pill bottle opener:
How Can I Get the Shelf Liner to Slide More Easily?
When the shelf liner or rug grip is laying down on the sewing machine, it can be a little bit difficult to slide as you are sewing.
I didn’t have much of a problem using the shelf liner from the Dollar Tree, however other people complain about the grip not allowing them to move the fabric easily underneath the needle.
If you have a problem, lay a piece of parchment paper or tissue paper on the left hand side of your sewing machine up to the metal plate where your needle inserts into your fabric.
Then tape down the parchment paper or tissue paper with painter’s tape or another type of tape that can be easily removed.
Helpful Tips I Learned From Sewing This Project
- You can use any size of square that you would like.
- You may want to add a loop to the opener to hang on the refrigerator or inside a cabinet.
- Stitching a large X through the lid opener prevents the fabric from bunching up and looking weird after multiple uses. However, this is a purely aesthetic thing and doesn’t help open the jars any more easily.
Perfect Craft Fair Items
DIY Pill Bottle Openers are PERFECT items to make to sell at craft fairs! You can make several in an hour and the low price of the materials lets you keep more money as profit.
Here is the estimated cost to make one jar opener:
- Fabric: $3.99/yd = .20 cents per square
- Shelf Liner: $1.25/roll = .15 cents per square
Total cost is 0.35 cents per jar opener or less!
Price these for $3-5 at craft fairs and online shops. They would also make a great value-added addition to a jar opener. Sell them together in a set.
Want to save this idea for later? Just Pin It to Pinterest or add it to Flipboard.
This easy sewing project is just one of the many DIY projects we have for your home. See these ideas next:
